Filing a claim is easier with good records. We document everything and talk to your adjuster for you.
We look at the damage, explain what it needs and give you a written price before we start.
Call now and a real person picks up. We ask a few questions and send a crew, so the water stops spreading sooner.
You do not have to work out how bad it is on your own. Call, tell us what you see, and a Staten Island technician will explain the next step and what it should cost.
There are two ways an attic ends up wet. Rain gets in from above through worn shingles, failed flashing, or the seals around vents and chimneys. From below, household moisture rises and condenses on the cold roof sheathing if attic ventilation is poor. Either way, hardly anyone goes up there to look. In Staten Island, we inspect the attic, track down the source, and get it dry.
Most attic jobs center on wet insulation. Heating and cooling bills go up because cellulose and fiberglass alike give up R-value when wet. The bigger problem is that for weeks, saturated insulation holds moisture on the drywall of the ceiling and on the framing. Saturated material comes out, air movers and dehumidifiers dry the wood, and any mold on the sheathing or rafters gets treated.
To learn whether you have a leak, condensation or the two together, we go over the roof deck, the vents, the exhaust ducts and each flashing point. How far it spread is shown by moisture meters and thermal imaging.
Insulation that is soaked or has mold gets bagged and carried out, giving the wood and the drywall below a chance to dry. The access path is kept contained and the living area underneath is protected.
With dehumidifiers and air movers, the sheathing, joists and rafters return to normal moisture levels. We clean visible mold off the wood, then apply an antimicrobial.
We point out the roof or ventilation problem that needs correcting and can share our findings with your roofer. Once the attic stays dry, new insulation goes in to restore the R-value.
Insulation that is damp and compressed barely insulates, and drying may not bring it back. The rooms beneath that section get colder or hotter, and you pay more for energy.
Some bathroom fans exhaust into the attic and never reach the outdoors, adding warm, damp air daily. That moisture condenses on the cold sheathing and looks just like a roof leak.
Attics hold junction boxes, recessed light housings and cable runs. Water in or on them is a shock and fire risk, so stay out until the power is checked.
Poorly ventilated attics often grow mold across the underside of the sheathing. It can cover a wide area before anyone goes up to look.
We save what can be dried properly and remove only what cannot. Moisture readings make that call, not guesswork.
Ask a Tech: (239) 268-6506| Material | Can usually be saved when | Has to be replaced when |
|---|---|---|
| Fiberglass insulation | Clean rainwater, a small wet patch, and it is dried quickly | Matted, dirty, moldy, or wet for more than a few days |
| Rafters and joists | Sound wood with nothing worse than light mold or surface stains | Rot that a screwdriver sinks into, or visible cracking |
| Ceiling drywall | A dry, flat stain that can be sealed and repainted | Weeks beneath saturated insulation, or any sagging or crumbling |
| Insulated ductwork | Dry inside, with an outer jacket that is not torn | The wrap holds water, has grown mold, or is pulling the duct down |
| Cellulose insulation | Only the surface is damp and it is still loose | Soaked through or packed down, which is most of the time |
Rain that makes it through the roof falls into the insulation and is absorbed. Nothing shows indoors, so the leak goes unnoticed and the roof is not repaired.
In a still, warm attic, paper facing and wood that stay damp give mold ideal conditions. The sheathing, along with the top face of the drywall ceiling, is where growth can begin.
After repeated wetting, the insulation is saturated and water reaches the ceiling. Brown rings appear in the room below, and the drywall may start to sag.
Sheathing delaminates and loses its hold on the roofing nails. Mold spreads across large sections of the roof deck, and the rafters remain damp enough to decay.
Have a different question? Call us and we will answer it over the phone.
Call (239) 268-6506Take action now and prevent costly damage. Staten Island Restoration is ready to help.
Call (239) 268-6506 Now