Certified technicians, professional drying equipment and moisture readings you can see for yourself. No guesswork.
The sooner drying starts, the less there is to repair. Our phones are answered around the clock, with same-day visits when available.
You focus on your home. We put together the photos, readings and reports your insurance company needs.
Most people who call us have never dealt with wall and drywall water damage before. We walk you through it on the phone, then send a local crew with the right equipment.
A sheet of drywall behaves much as a wick does. When water reaches the bottom of a wall, the gypsum and paper draw it upward, often a foot or more above the level the water ever reached on the floor. Insulation and the rear of the panel can be wet through while the paint out front shows nothing unusual. That is why we check walls with a moisture meter instead of trusting how they look.
Not every wet wall has to be torn out. Firm panels wetted by clean water are frequently saved, in some cases with the baseboard taken off and small openings drilled so air can move inside the wall. When the wall is soft, crumbling, moldy or was soaked by dirty water, we make a flood cut, a straight line above the damage, and remove everything below it.
We save what can be dried properly and remove only what cannot. Moisture readings make that call, not guesswork.
Ask a Tech: (239) 268-6506| Material | Can usually be saved when | Has to be replaced when |
|---|---|---|
| Wall studs | Solid studs, as they dry readily with the wall opened | Only where rot or heavy mold has damaged the wood |
| Paint and wallpaper | Paint that stays bonded on a wall that dried flat | Vinyl wallpaper that traps moisture, and any peeling finish |
| Outlets and switches | Dry outlets and switches that pass testing | Outlets, switches and boxes that got wet inside |
| Wall insulation | Rigid or spray foam of the closed cell type, which sheds water | Soaked batts or blown cellulose that sag and will not dry |
| Plaster walls | Plaster that stays hard and bonded once dry | Plaster that crumbles to powder or has come loose from its backing |
On an exterior wall, water can soak the sheathing behind the insulation. Because it is slow to dry, we test it before any new drywall goes up.
Paper lining, darkness and stagnant air make the hidden side of a wall a perfect place for mold. You can have a clean looking painted surface with heavy growth right behind it.
Drywall hidden in back of cabinetry and built-in units tends to be missed and dries very slowly. We take readings through toe kicks and from the opposite side to find it.
Receptacles and cables sit low in the wall, right where water collects. Leave the outlets on a damp wall alone until someone has checked the circuit.
We scan each wall with a moisture meter and thermal camera and mark how high and how far the water traveled, including the opposite side and adjoining rooms.
You get a straight answer on what can be dried where it is and what must be removed, judged by the category of water, the time it sat and the firmness of the drywall.
For walls being saved, baseboards come off and air is directed into the cavity. On sections coming out, a straight flood cut is made and soaked insulation is removed.
Drying typically takes 3 to 5 days of air movement and dehumidification before the framing and surviving drywall meter dry. Then we insulate, hang and finish new drywall, reinstall trim and paint.
Moisture enters where the panel meets the floor and wicks upward from there. Baseboards and the bottom plate take on moisture.
The wet line rises higher, baseboards swell and paint begins to blister. Mold can start on the paper facing inside the cavity.
Gypsum softens and the paper lets go. Insulation slumps inside the wall, odor builds and mold spreads across the hidden back side.
Mold and the start of decay show up on framing that has been wet the whole time. A far larger section of wall needs tearing out and rebuilding.
Have a different question? Call us and we will answer it over the phone.
Call (239) 268-6506Take action now and prevent costly damage. Staten Island Restoration is ready to help.
Call (239) 268-6506 Now